Camioane articulate Cat® 730

Modelul Cat® 730 este echipat cu o cabina cu design de top, reproiectata pe baza informatiilor primite de la operatori din toata lumea pentru a spori confortul si usurinta de exploatare. Imbunatatirile includ comenzi noi, functii de protectie a transmisiei, sistemul de asistare cu troliu, sistemul avansat de control automat al tractiunii, sistemul de avertizare a rasturnarii cu asistenta de stabilitate si modul Eco, pentru optimizarea consumului de carburant

Utilaj nou, second-hand sau de inchiriat, dumneavoastra alegeti!

Specificatii tehnice

SPECIFICATII TEHNICE

Engine
Engine Model Cat® C13
Bore 130 mm
Stroke 157 mm
Displacement 12.5 l
Net Power - ISO 14396 276 kW
Gross Power - SAE J1995 280 kW
No Engine De-rating Below 3810 m
Peak Engine Torque Speed 1200 r/min
Peak Engine Torque Net (SAE J1349) 2120 N·m
Net Power - SAE J1349 274 kW
Engine Model - U.S. EPA Tier 4 Final/EU Stage V Cat C13
Peak Engine Torque Gross (SAE J1995) 2141 N·m
Weights
Rated Payload 28 t
Body Capacities
Heaped (SAE 2:1) 17.5 m³
Struck 13.3 m³
Tailgate Heaped SAE 2:1 18.8 m³
Tailgate Struck 13.9 m³
Transmission
Forward - 1 8 km/h
Forward - 2 15 km/h
Forward - 3 22 km/h
Forward - 4 34 km/h
Forward - 5 47 km/h
Forward - 6 55 km/h
Reverse - 1 9 km/h
Sound Levels
Interior Cab 72 dB(A)
Operating Weights
Front Axle - Empty 15000 kg
Front Axle - Loaded 18280 kg
Center Axle - Rated Load 12360 kg
Rear Axle - Loaded 16700 kg
Center Axle - Loaded 16920 kg
Total - Rated Load 28000 kg
Front Axle - Rated Load 3280 kg
Total - Loaded 51900 kg
Center Axle - Empty 4560 kg
Rear Axle - Empty 4340 kg
Total - Empty 23900 kg
Rear Axle - Rated Load 12360 kg
Service Refill Capacities
Fuel Tank 412 l
Cooling System 83 l
Hydraulic System 110 l
Engine Crankcase 38 l
Transmission 47 l
Final Drives/Differential 125 l
Output Transfer Gear Box 24 l
DEF Tank 20 l
Body Hoist
Raise Time 12 s
Lower Time 8 s
Steering
Lock to Lock 4.75 seconds @ 60 rpm
Standards
Brakes ISO 3450 – 2011
Cab - FOPS ISO 3449 Level II – 2005
Cab - ROPS ISO 3471 – 2008
Steering ISO 5010 – 2007
Body Plate
Type High strength Brinell HB450 wear resistant steel
Turning Circle
Turning Dimensions - Aisle Width 5332 mm
Turning Dimensions - Steer Angle - Left/Right 45°
Turning Dimensions - Inside Radius 3879 mm
Turning Dimensions - SAE Turning Radius 7470 mm
Note Dimensions are for machines equipped with 23.5R25 tires.
Turning Dimensions - Clearance Radius 8075 mm
Sound Levels
Note (1) The operator sound exposure Leq (equivalent sound pressure level) measured according to the work cycle procedures specified in ANSI/SAE J1166 OCT98 is 72 dB(A), for the cab offered by Caterpillar, when properly installed and maintained and tested...
Engine
Note (3) The net power advertised is the power available at the flywheel when the engine is equipped with alternator, air cleaner, muffler and fan at minimum speed.
Emissions The 730 meets Tier 4 Final and Stage V emission standards.
Note (2) The power ratings apply at rated speed of 1,800 rpm when tested under the conditions for the specified standard.
Note (1) The references to Tier 4 Final/Stage V include U.S. EPA Tier 4 Final, EU Stage V, Japan 2014 (Tier 4 Final), and Korea Tier 4 Final emission standards.
Note (4) Net power when the fan is at maximum speed is 254 kW (341 hp) per the SAE reference conditions.
Sound Levels
Note (2) Hearing protection may be needed when operating with an open operator station and cab (when not properly maintained or doors/windows open) for extended periods or in noisy environments.
Body Plate Thickness
Base Plate 13 mm
Side Plates 11 mm
Optimal Loader/Truck Pass Matching
Wheel Loaders: 966M/966M XE - Passes 4
Wheel Loader: 962M - Passes 4–5
Wheel Loader: 950M - Passes 5
Hydraulic Excavators: 336F/336F XE - Passes 5–6
Hydraulic Excavators: 349F/349F XE - Passes 4–5
Engine
Note (5) DEF used in Cat SCR systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1. ISO 22241-1 requirements are met by many brands of DEF, including those that carry the AdBlue or API...
Optimal Loader/Truck Pass Matching
Note An optimum system match gives you a major productivity advantage. The 730 is an excellent match for the Cat 349F and 336F Hydraulic Excavators; and Cat 972M, 966M, 962M and 950M Wheel Loaders. Having matched loading and hauling tools results in...
Body Plate Thickness
Front Plate 7 mm
Optimal Loader/Truck Pass Matching
Wheel Loaders: 972M/972M XE - Passes 3–4
Doriti un sfat sau o recomandare?

Contactati-ne acum!

Sunati-ne
+40747185657
CONTACTATI-NE

STIRI SI NOUTATI