Coal Bowl Scrapers Caterpillar 637K (TIER 2/STAGE II)
Utilaj nou, second-hand sau de inchiriat, dumneavoastra alegeti!
Machine Speed Limit
This feature is designed to take the place of top gear selection. If the machine top speed needs to be limited the operator can select the top speed through the display or the top speed can be set in ET. This will allow the machine to find the correct gear that works best for the engine and transmission. Allowing the engine and transmission to select the correct gear to pull the load in most cases resulting in a lower engine load factor and lower fuel burn verses using top gear selection that required the machine to run at engine speeds at or close to high idle.
Sequence Assist (Optional Attachment)
This option uses cylinder position sensors to automate bowl, apron and further implement controls throughout the four core work cycles: Dig, Haul, Unload and Return. When utilized this can reduce up to 14 individual operator commands per cycle. Sequence Assist simplifies control over the implements, reduces joystick usage, automatically controls cushion hitch, transmission hold and ejector.
Load Assist (Optional Attachment)
Is designed to help shorten the learning curve of inexperienced operators to ensure consistency and faster loading of material while reducing effort of the operator. Based on the speed of the machine, Load Assist automatically adjusts the cutting edge height to manage wheel slip and to ensure consistent and efficient loading in bulk earthmoving applications.
Advanced Cushion Hitch
With similar technology as the Cat® Advanced Ride Management seat suspension, this software allows the cushion hitch to prevent end stroke by having the ability to predict end stroke events and manage the rate of dampening. Resulting in reduced hitch maintenance and improved operator ride in rough conditions.
Cat Grade Control (Optional Attachment)
Intelligently ensures the machine does not cut below grade in the cut area or over fill in the fill area – avoiding rework and moving unnecessary material.
Brakes
Have been changed from an air actuated drum shoe brake to a hydraulic actuated tractor wet disc brake and a scraper dry caliper.
Cab Improved
The K Series cab interior improves operator comfort and visibility. The overall interior is 21% larger than the G Series cab.
Tractor Serviceability Improvement
The fuel, water and engine oil are relocated at ground level on the right hand side of the machine for easy access.
Ground Speed Control
Ground Speed Control sets the desired top speed by the operator if job site conditions or segment speed limits require a speed less than full run out. Machine Speed Limit is intended for use when top speed needs to be limited for longer durations and Ground Speed Control is intended for use when the top speed needs to be reduced for shorter segments or intermediate periods of time. The operator can set the desired top speed and the machine will find the correct gear that works best for the engine and transmission.
Payload Estimator (Optional Attachment)
The Payload Estimator will calculate the payload of the machine in tonnes or tons by measuring the bowl lift cylinder pressures at the beginning of the loaded haul segment. This feature works best when using Sequence Assist. Using Payload Estimator during testing has achieved better than 95% accuracy when compared to actual scale weights. The Payload Estimator feature comes automatically when a machine is ordered with Sequence Assist.
Fuel Economy Mode
This is a two part feature when selected. The first part of the feature lowers the transmission shift points allowing shifting to take place at lower rpms to aid in fuel savings. The second part of the Fuel Economy Mode allows the machine when operated at engine rpms less than full throttle to automatically vary the power distribution between the tractor and the scraper.
High Pressure Steering
K Series steering system design requires significantly less steering effort. The reduced steering effort will allow for decreased operator fatigue and a more efficient operator resulting in possible higher rates of production late in the work cycle.
Engine Over Speed Protection
In the event of an engine over speed situation, the compression brake or brakes will automatically engage with no operator input. The machine determines the over speed condition based on rate of acceleration and applies compression brakes automatically.
Differential Lock Engagement Protection
This standard feature allows the machine to prevent the operator from engaging the differential lock when damage could occur.
Tire Spin Reduction
This feature will allow the machine to control the slip of the tractor tires only.
SPECIFICATII TEHNICE
Engine | |
---|---|
Flywheel Power - Tractor/Scraper | 425 kW (570 hp)/216 kW (290 hp) |
Operating Specifications | |
Scraper Capacity - Heaped | 38 m³ |
Top Speed - Loaded | 55.8 km/h |
General | |
Fuel Tank Refill Capacity - Scraper | 1400 l |
Overall Shipping Height | 4.15 m |
Scraper Capacity - Heaped | 38 m³ |
Overall Width | 3.94 m |
Scraper Capacity - Struck | 31 m³ |
Dimensions | |
Width - Tractor | 3499 mm |
General | |
Maximum Depth of Spread | 535 mm |
Width - Cut | 3.51 m |
Dimensions | |
Length - Overall Machine - Standard | 15480 mm |
General | |
Operating Weight - Empty | 52425 kg |
Dimensions | |
Width - Overall Machine | 3937 mm |
Service Refill Capacities | |
Crankcase - Scraper | 24.5 l |
Travel Speeds - Runout | |
Transmission Gear - Third | 12.4 km/h |
Safety Criteria Compliance Standards | |
Brakes | ISO 3450:2011 |
General | |
Flywheel Power - Tractor | 425 kW |
Overall Length | 15480 mm |
Travel Speeds - Runout | |
Transmission Gear - Sixth | 30.6 km/h |
Dimensions | |
Height - Top of Cab | 3733 mm |
Implement Cycle Times | |
Bowl Raise | 3.5 s |
Travel Speeds - Runout | |
Transmission Gear - Eighth | 55.8 km/h |
Service Refill Capacities | |
Transmission System - Scraper | 49 l |
Cooling System - Scraper | 61 l |
Travel Speeds - Runout | |
Transmission Gear - Seventh | 41.95 km/h |
Service Refill Capacities | |
Fuel Tank | 1400 l |
Dimensions | |
Width - Rear Tire Centers | 2462 mm |
Travel Speeds - Runout | |
Transmission Gear - Reverse | 9.9 km/h |
Dimensions | |
Rear Axle - Rear of Machine | 2424 mm |
Travel Speeds - Runout | |
Transmission Gear - Second | 10 km/h |
Implement Cycle Times | |
Bail Lower | 2.1 s |
Service Refill Capacities | |
Transmission System - Tractor | 110 l |
General | |
Top Speed - Loaded | 55.8 km/h |
Travel Speeds - Runout | |
Transmission Gear - First | 5.5 km/h |
Implement Cycle Times | |
Apron Raise | 4 s |
Travel Speeds - Runout | |
Transmission Gear - Fourth | 16.9 km/h |
Dimensions | |
Ground Clearance - Tractor | 664 mm |
Front of Tractor to Front Axle | 3612 mm |
Height - Overall Shipping | 4140 mm |
Implement Cycle Times | |
Bowl Lower | 3.5 s |
Ejector Retract | 8.5 s |
Safety Criteria Compliance Standards | |
Reverse Alarm | ISO 9533:2010 |
Cab | |
Exterior Sound Power Level | The exterior sound power level for the standard machine (ISO 6393:2008) is 118 dB(A). |
General | |
180° Curb-to-Curb Turning Width | 12.98 m |
Safety Criteria Compliance Standards | |
Steering System | ISO 5010:2007 |
Implement Cycle Times | |
Ejector Extend | 8.5 s |
Dimensions | |
Axle to Vertical Hitch Pin | 509 mm |
Width - Inside of Bowl | 3404 mm |
Safety Criteria Compliance Standards | |
Rollover Protection Structure (ROPS) | ISO 3471:2008 for up to 21 282 kg (46,919 lb) |
Implement Cycle Times | |
Bail Raise | 1.5 s |
Dimensions | |
Width - Outside Rear Tires | 3636 mm |
Service Refill Capacities | |
Hydraulic System | 142 l |
Implement Cycle Times | |
Apron Lower | 3.8 s |
General | |
Engine Model - Tractor | Cat C18 ACERT™ |
Rated Engine RPM - Tractor | 1900 r/min |
Emissions | Cat C9.3 ACERT and Cat C18 ACERT engines meet U.S. EPA Tier 2/EU Stage II equivalent emission standards. |
Safety Criteria Compliance Standards | |
Falling Object Protective Structure (FOPS) | ISO 3449:2005 Level II |
General | |
Engine Model - Scraper | Cat C9.3 ACERT |
Tires - Scraper | 37.25R35**E3 |
Flywheel Power - Scraper | 216 kW |
Dimensions | |
Height - Scraper Blade Maximum | 538 mm |
Safety Criteria Compliance Standards | |
Seat Belt | SAE J386:FEB2006 |
General | |
Rated Engine RPM - Scraper | 2150 r/min |
Travel Speeds - Runout | |
Transmission Gear - Fifth | 22.7 km/h |
General | |
Tires - Tractor | 37.25R35**E3 |
Service Refill Capacities | |
Cooling System - Tractor | 75 l |
Crankcase - Tractor | 52 l |
General | |
Rated Load | 37 285 kg (82,200 lb)/37.285 tonnes (41.1 tons) |
Maximum Depth of Cut | 450 mm |
Cab | |
ROPS/FOPS | Meet ISO standards |
Dimensions | |
Wheel Base | 9576 mm |
Contactati-ne acum!