Incarcatoare compacte pe roti Cat® 906M

Incarcatorul compact pe roti Cat® 906M ofera performante ridicate, cu o versatilitate remarcabila. Sistemul hidraulic si trenul de rulare reglate de operator din mers adapteaza raspunsul utilajului la sarcina in lucru. Nivelurile reduse de zgomot, cabina spatioasa si comenzile intuitive va ajuta sa lucrati confortabil intreaga zi.

Utilaj nou, second-hand sau de inchiriat, dumneavoastra alegeti!

Cabina confortabila

  • Joystick-ul sensibil necesita putin efort la actionare si include un comutator de inaintare/neutru/marsarier, declansatoare pentru blocarea diferentialului si flux continuu, precum si comenzi pentru cea de-a treia functie hidraulica.
  • Acces facil in cabina datorita balustradelor amplasate ergonomic, treptelor si platformei de mari dimensiuni.
  • Vizibilitate superioara asupra uneltei de lucru, gratie parbrizului lat si incarcatorului Cat cu bara in Z optimizata.
  • Niveluri reduse de zgomot.
  • Aer conditionat optional, cu functii de dezghetare/degivrare.
  • Optional, scaun incalzit cu suspensie pneumatica, reglaj pentru zona lombara si inclinare a spatarului.

Operare usoara

Sistemul electrohidraulic de ultima generatie asigura un control fin cu efort minim, cu cicluri de lucru rapide. Joystick-ul multifunctional mentine un nivel de concentrare ridicat asupra lucrului. Utilajul este usor de controlat prin apasarea unui buton, care va permite sa il configurati cum doriti, in functie de aplicatie.

Articulatie de incarcare cu ridicare paralela

incarcatorul Cat® cu bara in Z optimizata combina eficienta de sapare a unei bare in Z traditionale cu posibilitatile de conectare a altor unelte, pentru un nivel inalt de performanta si flexibilitate.

  • Ridicarea paralela si fortele mari de inclinare pe intreaga plaja de operare va permit sa manevrati sarcinile beneficiind de un control precis si un nivel inalt de siguranta si incredere.
  • Articulatia ofera o excelenta vizibilitate a muchiei de taiere a cupei si a varfurilor furcilor.

Performante ridicate

Transmisia hidrostatica controlata electronic asigura o putere reglabila la sol si un control excelent al vitezei la sol pentru cicluri de excavare rapide si flexibilitatea de a efectua eficient o multitudine de sarcini, inclusiv sarcini de basculare la rotire completa si forte de rupere mari, seria M oferind astfel solutii pentru orice aplicatie.

Specificatii tehnice

SPECIFICATII TEHNICE

Engine
Net Power 55.3 kW
Rated Net Power - 2,400 rpm - SAE J1349 54.7 kW
Emissions *The Cat C3.3B DIT engine meets U.S. EPA Tier 4 Final/EU Stage V (Europe only) or U.S. EPA Tier 4 Final (North America only) emission standards.
Maximum Gross Power - SAE J1995 55.4 kW
Engine Model Cat® C3.3B DIT*
Maximum Gross Power - ISO 14396 54.6 kW
Rated Net Power - 2,400 rpm - ISO 9249 (1977)/EEC 80/1269 55.3 kW
Weights
Operating Weight 5600 kg
Service Refill Capacities
Fuel Tank 52 l
Hydraulic System - Including Tank 70 l
Engine Crankcase 11.2 l
Cooling System 16.5 l
Loader Hydraulic System
Relief Pressure - Tilt Cylinder Head 31000 kPa
Maximum Flow - Implement Pump - Auxiliary Function High Flow 116 l/min
3rd Function Maximum Working Pressure 23500 kPa
Maximum Working Pressure - Implement Pump 23500 kPa
Maximum Flow - Implement Pump - Auxiliary Function Standard Flow 73 l/min
Maximum Flow - Implement Pump 73 l/min
Relief Pressure - Tilt Cylinder Rod 19000 kPa
Operating Specifications
Rated Bucket Capacity 0.9 m³
Tipping Load - Straight - ISO 14397-1 3932 kg
Steering Articulation Angle - Each Direction 39°
Reach - Full Lift and 45° Dump 714 mm
Clearance - Full Lift and 45° Dump 2513 mm
Tipping Load - Full Turn - ISO 14397-1 3204 kg
Full Turn Tipping Load 3405 kg
Dimensions with Bucket (Approximate) - Standard Lift - With ISO Coupler
Reach - Bucket at 45°* 725 mm
Note (3) Dimensions listed are for a machine configured with general purpose buckets, bolt-on cutting edges, 75 kg (165 lb) operator, no air conditioner and Dunlop 405/70 SPT9 tires.
Width - Tread Center 1420 mm
Machine Width 1840 mm
Dig Depth** 95 mm
Note (2) **Vary with tire.
Width - Bucket 1890 mm
Length - Overall* 5469 mm
Length - Wheel Base 2170 mm
Height - Bucket Pin** 3227 mm
Operating Weight 5670 kg
Height - Ground Clearance** 300 mm
Clearance - Bucket at 45° * 2478 mm
Height - Ground to Cab** 2463 mm
Turning Radius - Over Bucket 4420 mm
Departure Angle 33°
Note (1) *Vary with bucket.
Turning Radius - Inside of Tires 2240 mm
Articulation Angle 39°
Clearance - Level Bucket** 3027 mm
Dump Angle at Full Lift 45°
Dimensions with Bucket (Approximate) - Standard Lift - With SSL Coupler
Width - Bucket 1890 mm
Turning Radius - Inside of Tires 2240 mm
Machine Width 1840 mm
Turning Radius - Over Bucket 4464 mm
Clearance - Bucket at 45° * 2359 mm
Dump Angle at Full Lift 45°
Length - Wheel Base 2170 mm
Operating Weight 5663 kg
Length - Overall* 5620 mm
Height - Bucket Pin** 3227 mm
Note (1) *Vary with bucket.
Note (3) Dimensions listed are for a machine configured with general purpose buckets, bolt-on cutting edges, 75 kg (165 lb) operator, no air conditioner and Dunlop 405/70 SPT9 tires.
Departure Angle 33°
Articulation Angle 39°
Clearance - Level Bucket** 3035 mm
Height - Ground Clearance** 300 mm
Reach - Bucket at 45°* 820 mm
Dig Depth** 107 mm
Width - Tread Center 1420 mm
Height - Ground to Cab** 2463 mm
Note (2) **Vary with tire.
Engine
Maximum Gross Power 54.6 kW
Buckets
Bucket Capacities 0.75 m³-1.5 m³ (1.0 yd³-2.0 yd³)
Cab
ROPS SAE J1040 MAY94, ISO 3471-1994.
FOPS SAE J/ISO 3449 APR98, Level II, ISO 3449 1992 Level II.
Loader Hydraulic System
Boost Flow Maximum Pressure 22000 kPa
Drive Train
Reverse - High Range 35 km/h
Forward - Range 2 20 km/h
Cab
Note (2) When properly installed and maintained, the cab offered by Caterpillar, when tested with doors, and windows closed as per work cycle procedures specified in ISO 6395 2008, results in operator sound exposure Leq (Equivalent sound pressure level) of...
Steering
Steering AC Cycle Times - Full Left to Full Right - 2,620 rpm 3 s
Loader Hydraulic System
Hydraulic Cycle Time - 1,000 rpm - Dump, at Maximum Lift Height 3 s
Hydraulic Cycle Time - 1,000 rpm - Raise, Ground Level to Maximum Lift 9.6 s
Steering
Maximum Steering Torque - 0° (Straight Machine) 50375 N·m
Engine
Stroke 120 mm
Steering
Maximum Steering Torque - 39° (Full Turn) 37620 N·m
Loader Hydraulic System
Hydraulic Cycle Time - 1,800 rpm - Dump, at Maximum Lift Height 1.5 s
Steering
Nominal Flow - Steering Pump 43.9 l/min
Loader Hydraulic System
Tilt Cylinder, Double Acting - Bore Diameter 90 mm
Service Refill Capacities
Axles - Front N/A
Hydraulic Tank 46 l
Tires
Option (3) 340/80 R18 XMCL Michelin
Drive Train
Forward - High Range 35 km/h
Engine
Maximum Gross Torque - ISO 14396 261 N·m
Tires
Note (1) *Standard tire.
Loader Hydraulic System
Hydraulic Cycle Time - 1,800 rpm - Float Down, Maximum Lift to Ground Level 2.6 s
Lift Cylinder, Double Acting - Bore Diameter 75 mm
Weights
Note Specifications shown are for a machine configured with general purpose buckets, bolt-on cutting edges, 75 kg (165 lb) operator, Dunlop 405/70 SPT9 tires, full fuel, comfort ROPS cab, standard flow hydraulics and skid-steer coupler. The 906M is...
Loader Hydraulic System
Hydraulic Cycle Time - 1,800 rpm - Total Cycle Time 9.6 s
Tilt Cylinder, Double Acting - Stroke 417 mm
Engine
Maximum Gross Power - DIN ISO 14396 54.6 kW
Steering
Steering Cylinder, Double Acting - Bore Diameter 80 mm
Drive Train
Reverse - Range 2 20 km/h
Tires
Option (5) 340/80 R18 Bibload Michelin
Engine
Displacement 3.3 l
Steering
Steering Cylinder, Double Acting - Stroke 300 mm
Buckets
Note All capacities are applicable for each model. Bucket selection must be made with an understanding of the material density and application to ensure machine stability is maintained within the tipping loads stated per model and configuration.
Engine
Maximum Net Torque - ISO 9249 (1977)/EEC 80/1269 260 N·m
Steering
Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left <6 turns
Engine - Tier 4 Final/Stage IV
Maximum Net Torque - SAE J1349 257 N·m
Drive Train
Forward - Range 1 10 km/h
Tires
Option (2) 340/80 R18 AT-R Firestone
Engine
Note (3) No derating required up to 3000 m (10,000 ft) altitude. Auto derate protects hydraulic and transmission systems.
Steering
Steering Cylinder, Double Acting - Rod Diameter 35 mm
Service Refill Capacities
Transmission - Gear Box 8.5 l
Buckets
General Purpose 0.8 m³ (1 yd³), 0.9 m³ (1.2 yd³), 1.0 m³ (1.3 yd³), 1.1 m³ (1.4 yd³), 1.3 m³ (1.7 yd³)
Loader Hydraulic System
Hydraulic Cycle Time - 1,800 rpm - Raise, Ground Level to Maximum Lift 5.5 s
Buckets
Light Material 1.2 m³ (1.6 yd³), 1.5 m³ (2.0 yd³)
Engine
Bore 94 mm
Loader Hydraulic System
Hydraulic Cycle Time - 1,000 rpm - Float Down, Maximum Lift to Ground Level 2.6 s
Drive Train
Reverse - Range 1 10 km/h
Engine
Note (4) Flywheel per the SAE reference conditions with the fan at maximum speed.
Tires
Note (2) Other tire choices available, contact your Cat dealer for details.
Steering
Maximum Working Pressure - Steering Pump 22000 kPa
Engine
Note (2) Net power shown is the power available at the flywheel when the engine is equipped with alternator, air cleaner, diesel exhaust filter, and fan at minimum speed.
Note (6) Stage V engine available for Europe only.
Tires
Option (6) 405/70 R18 SPT9 Dunlop*
Option (1) 335/80 R18 XZSL Michelin
Loader Hydraulic System
Lift Cylinder, Double Acting - Rod Diameter 50 mm
Buckets
Grapple 0.9 m³ (1.2 yd³) heaped
Cab
Note (1) Cat cab and Rollover Protective Structures (ROPS) are standard in North America and Europe.
Loader Hydraulic System
Lift Cylinder, Double Acting - Stroke 695 mm
Tires
Note (3) In certain applications, the loader's productive capabilities may exceed the tires' tonnes-km/h (ton-mph) capabilities.
Service Refill Capacities
Axles - Rear N/A
Buckets
Multi-Purpose 0.75 m³ (1.0 yd³), 0.9 m³ (1.2 yd³), 1.05 m³ (1.37 yd³)
Loader Hydraulic System
Tilt Cylinder, Double Acting - Rod Diameter 55 mm
Engine
Note (5) The Cat C3.3B DIT Tier 4 Final/Stage V uses an active regeneration system which requires no operator interaction under normal conditions.
Tires
Option (7) 12.5/80 R18 Flexport™
Note (4) Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model.
Steering
Steering Articulation Angle - Each Direction 39°
Tires
Option (4) 340/80 R18 TRI2 Nokian
Engine
Note (1) Net power ratings are tested at the reference conditions for the specified standard.
Doriti un sfat sau o recomandare?

Contactati-ne acum!

Sunati-ne
+40747185657
CONTACTATI-NE

STIRI SI NOUTATI